Advance Ply Gold Marine
- Home
- All Plywood Range
- Advance Ply Gold Marine
- 35 Year Warranty
- 100% Hardwood Construction
- E1 Grade Resin
- 0.75 g/cm³ Density
- 200 Hours BWP
- IS 710 Marine Grade
Thickness Selector
Back panels, drawer bottoms, light marine cladding and protective panels. Not for load bearing panels or fixings carrying weight.
Partition panels, boat interiors, wall cladding and lightweight exterior applications. Suits vertical panels that do not carry shelf loads.
Internal shelves, storage units, wet area furniture and secondary structural panels. The usual minimum where a panel holds weight in a wet area.
Doors, outdoor furniture, balcony storage and semi structural applications. Used where hinge and handle fixings take repeated stress.
Marine furniture, kitchen carcasses, bathroom vanities, coastal installations and heavy duty furniture carcasses. The most specified thickness in the range.
Standard 8×4 ft. Also available in 7×4 ft, 6×4 ft, 8×3 ft, 7×3 ft and 6×3 ft.
- Marine Grade
- IS 710:2024
- 100% Hardwood
- 0.75 g/cm³ Density
- 1600N+ Screw Holding
- HEXAPRO Process
- HVRT Technology
- 4x Pressed
- CCB Treated
- Anti Fungal
- Termite and Borer Treated
- E1 Resin
- Both Side Calibrated
Advance Ply Gold Marine is IS 710:2024 certified boiling water proof marine grade plywood, built for sustained contact with water, humidity and coastal air. IS 710 and the marine grade designation are printed on the edge of every sheet, alongside the ISI mark and the CM/L licence number.
This is the dedicated marine board in the Advance Ply range. Tungsten and Palladium add IS 5509 fire retardant certification for projects governed by fire regulations. Gold Marine carries IS 710 alone, which is the right specification for the large majority of residential and coastal wet area work, where a fire certification is never asked for and does not need to be paid for.
The board is built from 100% tropical hardwood veneers bonded with E1 grade phenol formaldehyde resin. Average density is 0.75 g/cm³, screw and nail holding is above 1600 N, compressive strength is above 5500 N, and the glue line holds through up to 200 hours of boiling water without delamination. IS 710:2024 requires 72 hours.
Every sheet goes through the HEXAPRO process: four hydraulic press cycles and two chemical treatments before it leaves the factory. Resin penetration into the core is handled separately by HVRT, High Viscous Resin Technology. Preservative protection is Copper Chrome Boron, and the board carries anti fungal and termite and borer marks alongside it.
Gold Marine is specified for marine construction including boat interiors and dock structures, coastal buildings, modular kitchen carcasses, bathroom vanities, outdoor and garden furniture, balcony flooring and wet area cladding. It is the grade to use anywhere standard BWR plywood would fail from direct water contact.
Why Advance Ply Gold Marine Performs Differently?
IS 710
Marine Grade
Certified by the Bureau of Indian Standards under IS 710:2024, with the IS number, the ISI mark and the CM/L licence number printed on the board edge.
Up To 200 Hours
Boiling Water Proof
The glue line holds through up to 200 hours of continuous boiling without delamination. IS 710:2024 requires 72 hours, so the board is tested well beyond the standard.
35 Year
Warranty
A 35 year manufacturer warranty, issued as a certificate registered against the invoice.
4x
Hydraulic Press Cycles
The HEXAPRO process presses every sheet four times and treats it twice. Additional press cycles reduce internal air gaps, raise density and improve bonding between veneers.
100%
Hardwood Construction
Tropical hardwood veneers throughout, which is what holds density at 0.75 g/cm³ and keeps screw and nail holding above 1600 N.
CCB
Termite and Fungal Protection
Copper Chrome Boron treatment against termites, borers and fungal decay, with anti fungal and termite and borer marks printed on the board.
HEXAPRO is the Advance Ply manufacturing process: six stages made up of four press cycles and two chemical treatments. Each press cycle compresses the veneer stack further, which is what holds density at 0.75 g/cm3 and keeps a screw above 1600 N.
HVRT is a separate technology doing a different job. High Viscous Resin Technology controls how deeply the resin travels into the core rather than sitting between the face veneers. Deep penetration is what keeps the glue line intact through up to 200 hours of boiling water.
Water resistance on its own is not durability. A board that survives moisture but is eaten from the inside has still failed, which is why IS 710 makes preservative treatment mandatory. Gold Marine is Copper Chrome Boron treated and carries anti fungal and termite and borer marks on the board itself.
Both sides are calibrated to a uniform thickness, which matters when the board goes into CNC work, edge banding or architectural joinery where a fraction of a millimetre shows in the finished joint.
Advance Ply Gold Marine Technical Specifications
Specification | Value |
|---|---|
Physical Properties | |
| Plywood Type | BWP Marine Grade Plywood |
| IS Standard | IS 710:2024, marine grade |
| BIS Licence | CM/L number printed on every board edge alongside the ISI mark |
| Base Material | 100% hardwood construction |
| Face Material | Tropical hardwood species |
| Density | Average 0.75 g/cm³ |
| Thickness Range | 6mm to 19mm |
| Standard Sheet Sizes | 8x4 ft, 7x4 ft, 6x4 ft, 8x3 ft, 7x3 ft, 6x3 ft |
| Calibrated | Yes, both sides |
| Moisture Content | 5%–15% (Oven Dry Method) |
| Board Traceability | Batch number, date of manufacture and a scannable QR code printed on every sheet |
| Weather Resistance | Withstands adverse climatic conditions |
Resin and Preservation Properties | |
| Resin Type | E1 grade phenol formaldehyde resin |
| Formaldehyde Emission | E1 grade, low formaldehyde emission |
| Resin Technology | HVRT, High Viscous Resin Technology |
| CCB Treatment | Core treated with Copper Chrome Boron |
| CCB Retention | More than 12% |
| Biological Protection | Anti fungal, termite and borer treated |
| Resistance To Microorganism | Average Strength More Than 1700 N |
Mechanical Properties | |
| Screw Holding Capacity | More Than 1600 N |
| Compressive Strength | More Than 5500 N |
| Modulus Of Elasticity (Dry) | Along Grain: Avg 6589 N/mm², Min 6036 N/mm² | Across Grain: Avg 4890 N/mm², Min 4352 N/mm² |
| Modulus Of Rupture (Dry) | Along Grain: Avg 49 N/mm², Min 43 N/mm² | Across Grain: Avg 40 N/mm², Min 36 N/mm² |
| Modulus Of Elasticity (Wet) | Along Grain: Avg 3456 N/mm², Min 3289 N/mm² | Across Grain: Avg 2564 N/mm², Min 2340 N/mm² |
| Modulus Of Rupture (Wet) | Along Grain: Avg 27 N/mm², Min 25 N/mm² | Across Grain: Avg 22 N/mm², Min 20 N/mm² |
| Tensile Strength | Along Grain: 48 N/mm² | Across Grain: 39 N/mm² | Combined: 87 N/mm² |
| Glue Shear Strength (Dry) | Avg 1456 N/mm², Min 1348 N/mm² |
| Glue Shear Strength (Wet) | Avg 1310 N/mm², Min 1236 N/mm² |
Water Resistance | |
| Boiling Water Proof | 200 hours without delamination |
| Water Resistance | Designed for continuous high moisture exposure |
Manufacturing | |
| Manufacturing Process | HEXAPRO, four press cycles and two chemical treatments |
| Resin Technology | HVRT, High Viscous Resin Technology |
| Press Cycles | 4x hydraulic pressing |
| Bonding System | Phenol formaldehyde marine grade bonding |
| Surface | Matt ply, both side calibrated |
Warranty | |
| Warranty | 35 Year Manufacturer Warranty |
Advance Ply Gold Marine Features, Advantages and Benefits
Feature | Advantage | Benefit |
|---|---|---|
| E1 BWP grade resin | Water proof grade bonding with low emission and no harmful gases released into the room | Strong water proofing and healthier indoor air |
| IS 710 grade | Certified marine grade plywood | Can be used in exterior conditions and severe humid environments |
| Boiling water proof for 200 hours | Long lasting bond even under high moisture or humidity | Very high water proofing and long product life |
| All glue lines CCB treated | Stops insects and fungus attacking the board | No powder formation, decay or termite damage in the furniture |
| HVRT high viscous resin technology | Resin spreads evenly and penetrates deep into the core | Uniform bonding and strength through every layer |
| 100% hardwood construction | Denser, more stable panel than mixed core boards | Better nail and screw holding where load bearing is needed |
| Both side calibrated | Uniform thickness across the full sheet | Clean fit in CNC work, edge banding and architectural joinery |
Advance Ply Gold Marine vs Other Advance Ply Plywood Range
| Feature | Gold Marine (this) | Tungsten | Palladium |
|---|---|---|---|
| IS standard | IS 710:2024 | IS 710:2024 and IS 5509:2021 | IS 710:2024 and IS 5509:2021 |
| Grade type | BWP marine grade | BWP marine and Fire Retardant grade | BWP marine and Fire Retardant grade |
| Fire retardant (IS 5509) | No | Yes | Yes |
| Resin emission class | E1 | E0 | E1 |
| Density | 0.75 g/cm³ | 0.78 g/cm³ | 0.75 g/cm³ |
| Core construction | 100% hardwood | 100% hardwood, 13 layer | 100% hardwood |
| Boiling water performance | Up to 200 hours | Up to 250 hours | Up to 200 hours |
| Compressive strength | More than 5500 N | More than 6000 N | More than 5500 N |
| Screw Holding Capacity | More than 1600 N | More than 1600 N | More than 1600 N |
| Warranty | 35 years | Lifetime | 36 years |
| Best for | Marine and coastal work, residential kitchens and bathrooms, outdoor furniture, any wet area with no fire requirement | Fire governed commercial wet areas, modular kitchens, hospitals, hotels, schools | Wardrobes, premium furniture, commercial interiors and large fire governed projects |
The practical reading is short. All three are IS 710 marine grade and all three will hold in a wet area. Tungsten and Palladium add fire certification and longer warranties. If the project has no fire requirement, Gold Marine delivers the same boiling water proof performance without paying for a certification that will never be asked for.
Frequently Asked Questions About Advance Ply Gold Marine
What is Advance Ply Gold Marine used for?
Advance Ply Gold Marine is used for marine construction (boat interiors, dock structures), coastal buildings, outdoor kitchens, garden furniture, balcony flooring, and any application with sustained direct water or humidity exposure. It is IS 710 certified BWP marine grade plywood that withstands prolonged boiling water immersion without delaminating.
Is Advance Ply Gold Marine genuinely IS 710 certified?
Yes. Gold Marine carries IS 710:2024 certification from the Bureau of Indian Standards, and the IS number, the ISI mark and the CM/L licence number are printed on the edge of every sheet. IS 710 requires the board to survive 72 hours of continuous boiling without delamination, along with checks on preservative treatment, fungal resistance and mechanical strength in both dry and wet condition. Gold Marine is tested to 200 hours.
Is Gold Marine boiling water proof or boiling water resistant?
Boiling water proof. BWP is the grade defined by IS 710 and it is the highest water performance grade under Indian Standards. Boiling water resistant is BWR grade under IS 303, which is a different and lower specification.
What is the difference between Advance Ply Gold Marine and Advance Ply Tungsten?
Both are IS 710 marine grade, 100% hardwood, CCB treated and pressed four times through the HEXAPRO process. Tungsten adds IS 5509 fire retardant certification, E0 resin, 13 layer construction, 0.78 g/cm³ density, 250 boiling hours and a lifetime warranty. Gold Marine carries IS 710 only, with E1 resin, 0.75 g/cm³, 200 boiling hours and a 35 year warranty.
Why would I choose Gold Marine over Tungsten or Palladium?
Because most residential and coastal wet area work has no fire requirement. Tungsten and Palladium carry IS 5509 fire retardant certification, which matters in hotels, hospitals, schools and commercial buildings governed by fire regulations. If your project will never be asked to prove fire compliance, Gold Marine gives you the same IS 710 boiling water proof performance without that certification.
Can Gold Marine be used for modular kitchen cabinets?
Yes. Gold Marine is IS 710 BWP certified and is suitable for modular kitchen cabinets. Both Tungsten and Gold Marine are suitable for kitchen applications. If the project also requires IS 5509 fire retardant compliance (commercial kitchens, restaurants), specify Tungsten.
Is Advance Ply Gold Marine suitable for outdoor use?
Yes. IS 710 certified BWP marine grade plywood is designed for outdoor and coastal applications. It withstands prolonged moisture, humidity, and water exposure without delaminating. Edge sealing with approved marine sealant is recommended for all outdoor applications to protect cut edges.
Does Advance Ply Gold Marine carry IS 5509 fire retardant certification?
No. Gold Marine carries IS 710 BWP certification only. For projects requiring both boiling waterproof and fire retardant plywood, specify Advance Ply Tungsten which carries both IS 710 and IS 5509 certifications.
Advance Ply Gold Marine - Marine Grade Plywood
IS 710 | E1 Grade Resin | HEXAPRO Process | Up to 200 Hours Boiling Water Proof | 35 Year Warranty
